Butyl methacrylate Safety Data Sheets
SAFETY DATA SHEETS
According to the UN GHS revision 8
SECTION 1: Identification
1.1 GHS Product identifier
| Product name | Butyl methacrylate |
|---|
1.2 Other means of identification
| Product number | - |
|---|---|
| Other names | BUTYLMETHACRYLATE; BUTYL METHACRYLATE (100 ML ); N-BUTYL METHACRYLATE/METHACRYLIC ACID BUTYL ESTER |
1.3 Recommended use of the chemical and restrictions on use
| Identified uses | Intermediates |
|---|---|
| Uses advised against | no data available |
1.4 Supplier's details
| Company | Echemi.com |
|---|---|
| Address | Echemi.com |
| Telephone | Echemi.com |
1.5 Emergency phone number
| Emergency phone number | Echemi.com |
|---|---|
| Service hours | Monday to Friday, 9am-5pm (Standard time zone: UTC/GMT +8 hours). |
SECTION 2: Hazard identification
2.1 Classification of the substance or mixture
Flammable liquids, Category 3
Skin irritation, Category 2
Eye irritation, Category 2
Skin sensitization, Category 1
Specific target organ toxicity â single exposure, Category 3
2.2 GHS label elements, including precautionary statements
| Pictogram(s) |   |
|---|---|
| Signal word | Warning |
| Hazard statement(s) | H226 Flammable liquid and vapour H315 Causes skin irritation H319 Causes serious eye irritation H317 May cause an allergic skin reaction H335 May cause respiratory irritation |
| Precautionary statement(s) | |
| Prevention | P210 Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. No smoking. P233 Keep container tightly closed. P240 Ground and bond container and receiving equipment. P241 Use explosion-proof [electrical/ventilating/lighting/...] equipment. P242 Use non-sparking tools. P243 Take action to prevent static discharges. P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/... P264 Wash ... thoroughly after handling. P261 Avoid breathing dust/fume/gas/mist/vapours/spray. P272 Contaminated work clothing should not be allowed out of the workplace. P271 Use only outdoors or in a well-ventilated area. |
| Response | P303+P361+P353 IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse affected areas with water [or shower]. P370+P378 In case of fire: Use ... to extinguish. P302+P352 IF ON SKIN: Wash with plenty of water/... P321 Specific treatment (see ... on this label). P332+P317 If skin irritation occurs: Get medical help. P362+P364 Take off contaminated clothing and wash it before reuse. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. P333+P317 If skin irritation or rash occurs: Get medical help. P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing. P319 Get medical help if you feel unwell. |
| Storage | P403+P235 Store in a well-ventilated place. Keep cool. P403+P233 Store in a well-ventilated place. Keep container tightly closed. P405 Store locked up. |
| Disposal | P501 Dispose of contents/container to an appropriate treatment and disposal facility in accordance with applicable laws and regulations, and product characteristics at time of disposal. |
2.3 Other hazards which do not result in classification
no data available
SECTION 3: Composition/information on ingredients
3.1 Substances
| Chemical name | Common names and synonyms | CAS number | EC number | Concentration |
|---|---|---|---|---|
| Butyl methacrylate | Butyl methacrylate | 97-88-1 | 202-615-1 | 100% |
SECTION 4: First-aid measures
4.1 Description of necessary first-aid measures
If inhaled
Fresh air, rest. Half-upright position. Refer for medical attention.
Following skin contact
Remove contaminated clothes. Rinse and then wash skin with water and soap. Refer for medical attention .
Following eye contact
Rinse with plenty of water (remove contact lenses if easily possible).
Following ingestion
Rinse mouth. Do NOT induce vomiting. Refer for medical attention .
4.2 Most important symptoms/effects, acute and delayed
Inhalation may cause nausea because of offensive odor. Contact with liquid causes irritation of eyes and mild irritation of skin. Ingestion causes irritation of mouth and stomach. (USCG, 1999)
4.3 Indication of immediate medical attention and special treatment needed, if necessary
Immediate first aid: Ensure that adequate decontamination has been carried out. If patient is not breathing, start artificial respiration, preferably with a demand-valve resuscitator, bag-valve-mask device, or pocket mask, as trained. Perform CPR as necessary. Immediately flush contaminated eyes with gently flowing water. Do not induce vomiting. If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain an open airway and prevent aspiration. Keep patient quiet and maintain normal body temperature. Obtain medical attention. Esters and related compounds
SECTION 5: Fire-fighting measures
5.1 Suitable extinguishing media
Foam, dry chemical, carbon dioxide.
5.2 Specific hazards arising from the chemical
Behavior in Fire: Containers may explode due to polymerization. (USCG, 1999)
5.3 Special protective actions for fire-fighters
Use foam, carbon dioxide. In case of fire: keep drums, etc., cool by spraying with water.
SECTION 6: Accidental release measures
6.1 Personal precautions, protective equipment and emergency procedures
Personal protection: filter respirator for organic gases and vapours adapted to the airborne concentration of the substance. Do NOT let this chemical enter the environment. Collect leaking liquid in sealable containers. Absorb remaining liquid in sand or inert absorbent. Then store and dispose of according to local regulations.
6.2 Environmental precautions
Personal protection: filter respirator for organic gases and vapours adapted to the airborne concentration of the substance. Do NOT let this chemical enter the environment. Collect leaking liquid in sealable containers. Absorb remaining liquid in sand or inert absorbent. Then store and dispose of according to local regulations.
6.3 Methods and materials for containment and cleaning up
SRP: Wastewater from contaminant suppression, cleaning of protective clothing/equipment, or contaminated sites should be contained and evaluated for subject chemical or decomposition product concentrations. Concentrations shall be lower than applicable environmental discharge or disposal criteria. Alternatively, pretreatment and/or discharge to a permitted wastewater treatment facility is acceptable only after review by the governing authority and assurance that "pass through" violations will not occur. Due consideration shall be given to remediation worker exposure (inhalation, dermal and ingestion) as well as fate during treatment, transfer and disposal. If it is not practicable to manage the chemical in this fashion, it must be evaluated in accordance with EPA 40 CFR Part 261, specifically Subpart B, in order to determine the appropriate local, state and federal requirements for disposal.
SECTION 7: Handling and storage
7.1 Precautions for safe handling
NO open flames, NO sparks and NO smoking. Above 50°C use a closed system, ventilation and explosion-proof electrical equipment. Prevent build-up of electrostatic charges (e.g., by grounding). Handling in a well ventilated place. Wear suitable protective clothing. Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Use non-sparking tools. Prevent fire caused by electrostatic discharge steam.
7.2 Conditions for safe storage, including any incompatibilities
Fireproof. Separated from oxidants. Cool. Dry. Keep in the dark. Store only if stabilized. Store in an area without drain or sewer access.Temp during storage must be kept low to minimize formation of peroxides and other oxidation products ... Storage temp below 30 deg C are recommended for the polyfunctional methacrylates ... The methacrylate monomers should not be stored for longer than one year. Shorter storage times are recommended for the aminomethacrylates, ie, three months, and the polyfunctional methacrylates, ie, six months. Many of these cmpd are sensitive to UV light and should, therefore, be stored in the dark. The methacrylic esters may be stored in mild steel, stainless steel, or aluminum. Methacrylic acid & derivatives
SECTION 8: Exposure controls/personal protection
8.1 Control parameters
Occupational Exposure limit values
MAK sensitization of skin (SH)
Biological limit values
no data available
8.2 Appropriate engineering controls
Ensure adequate ventilation. Handle in accordance with good industrial hygiene and safety practice. Set up emergency exits and the risk-elimination area.
8.3 Individual protection measures, such as personal protective equipment (PPE)
Eye/face protection
Wear safety goggles.
Skin protection
Protective gloves. Protective clothing.
Respiratory protection
Use ventilation, local exhaust or breathing protection.
Thermal hazards
no data available
SECTION 9: Physical and chemical properties and safety characteristics
| Physical state | N-butyl methacrylate is a clear colorless liquid. Flash point 130°F. Less dense (7.5 lb / gal) than water and insoluble in water. Hence floats on water. Vapors heavier than air. Used to make resins adhesives, and oil additives. |
|---|---|
| Colour | Colorless liquid |
| Odour | Faint characteristic odor of esters |
| Melting point/freezing point | -25°C(lit.) |
| Boiling point or initial boiling point and boiling range | 162-165°C(lit.) |
| Flammability | Flammable. |
| Lower and upper explosion limit/flammability limit | Lower flammable limit: 2% in air; Upper flammable limit: 8% in air (estimates) |
| Flash point | 54°C |
| Auto-ignition temperature | 562°F |
| Decomposition temperature | no data available |
| pH | no data available |
| Kinematic viscosity | 3.116 cP at 70 deg F |
| Solubility | Insoluble (NTP, 1992) |
| Partition coefficient n-octanol/water | log Kow = 2.88 |
| Vapour pressure | 2 mm Hg ( 20 °C) |
| Density and/or relative density | 0.894g/mLat 25°C(lit.) |
| Relative vapour density | 4.91 (15 °C, vs air) |
| Particle characteristics | no data available |
SECTION 10: Stability and reactivity
10.1 Reactivity
The substance may polymerize due to heating, under the influence of moisture, oxidants or light. This generates fire or explosion hazard.
10.2 Chemical stability
no data available
10.3 Possibility of hazardous reactions
FlammableAs a result of flow, agitation, etc., electrostatic charges can be generated.N-BUTYL METHACRYLATE reacts exothermically with acids. Reacts with oxidizing agents. Strong oxidizing acids may cause a reaction that is sufficiently exothermic to ignite the reaction products. Heat is generated with caustic solutions. Generates flammable hydrogen with alkali metals and hydrides. Polymerizes easily (NTP, 1992).
10.4 Conditions to avoid
no data available
10.5 Incompatible materials
May accumulate static electrical charges and cause ignition of its vapors.
10.6 Hazardous decomposition products
When heated to decomp it emits acrid smoke and irritating fumes.
SECTION 11: Toxicological information
Acute toxicity
- Oral: LD50 Mouse oral 15,800 mg/kg
- Inhalation: LC50 Rat inhalation 19.7 mg/L (approx 3388 ppm) (hypercolemia of organs, emphysematous swelling and point hemorrhages of lungs; circulation disturbances in the organs persisted for 2 weeks, emphysema and lung hemorrhages for one month)
- Dermal: no data available
Skin corrosion/irritation
no data available
Serious eye damage/irritation
no data available
Respiratory or skin sensitization
no data available
Germ cell mutagenicity
no data available
Carcinogenicity
no data available
Reproductive toxicity
no data available
STOT-single exposure
Lachrymation. The substance is irritating to the eyes, skin and respiratory tract. If swallowed the substance may cause vomiting and could result in aspiration pneumonitis. Medical observation is indicated.
STOT-repeated exposure
Repeated or prolonged contact may cause skin sensitization.
Aspiration hazard
No indication can be given about the rate at which a harmful concentration of this substance in the air is reached on evaporation at 20°C.
SECTION 12: Ecological information
12.1 Toxicity
- Toxicity to fish: LC50; Species: Pimephales promelas (Fathead minnow); Conditions: flow-through; Concentration: 11 mg/L for 96 hr
- Toxicity to daphnia and other aquatic invertebrates: EC50; Species: Daphnia magna (water flea); Conditions: static, closed vessels; Concentration: 32 mg/L for 48 hr; Effect: immobilization
- Toxicity to algae: EC50; Species: Pseudokirchneriella subcapitata (algae); Conditions: static; Concentration: 130 mg/L for 72 hr; Effect: growth rate
- Toxicity to microorganisms: no data available
12.2 Persistence and degradability
AEROBIC: n-Butyl methacrylate reached 38% of its theoretical BOD after 28 days(1). n-butyl methacrylate, present at 100 mg/L, reached 88% of its Theoretical BOD in 4 weeks using an activated sludge inoculum at 30 mg/L in the Japanese MITI test(2).
12.3 Bioaccumulative potential
An estimated BCF of 37 was calculated in fish for n-butyl methacrylate(SRC), using a log Kow of 2.88(1) and a regression-derived equation(2). According to a classification scheme(3), this BCF suggests the potential for bioconcentration in aquatic organisms is moderate(SRC).
12.4 Mobility in soil
Using a structure estimation method based on molecular connectivity indices(1), the Koc of n-butyl methacrylate can be estimated to be 55(SRC). According to a classification scheme(2), this estimated Koc value suggests that n-butyl acrylate is expected to have high mobility in soil.
12.5 Other adverse effects
no data available
SECTION 13: Disposal considerations
13.1 Disposal methods
Product
The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems.
Contaminated packaging
Containers can be triply rinsed (or equivalent) and offered for recycling or reconditioning. Alternatively, the packaging can be punctured to make it unusable for other purposes and then be disposed of in a sanitary landfill. Controlled incineration with flue gas scrubbing is possible for combustible packaging materials.
SECTION 14: Transport information
14.1 UN Number
| ADR/RID: UN2227 (For reference only, please check.) | IMDG: UN2227 (For reference only, please check.) | IATA: UN2227 (For reference only, please check.) |
14.2 UN Proper Shipping Name
| ADR/RID: n-BUTYL METHACRYLATE, STABILIZED (For reference only, please check.) | IMDG: n-BUTYL METHACRYLATE, STABILIZED (For reference only, please check.) | IATA: n-BUTYL METHACRYLATE, STABILIZED (For reference only, please check.) |
14.3 Transport hazard class(es)
| ADR/RID: 3 (For reference only, please check.) | IMDG: 3 (For reference only, please check.) | IATA: 3 (For reference only, please check.) |
14.4 Packing group, if applicable
| ADR/RID: III (For reference only, please check.) | IMDG: III (For reference only, please check.) | IATA: III (For reference only, please check.) |
14.5 Environmental hazards
| ADR/RID: No | IMDG: No | IATA: No |
14.6 Special precautions for user
no data available
14.7 Transport in bulk according to IMO instruments
no data available
SECTION 15: Regulatory information
15.1 Safety, health and environmental regulations specific for the product in question
| Chemical name | Common names and synonyms | CAS number | EC number |
|---|---|---|---|
| Butyl methacrylate | Butyl methacrylate | 97-88-1 | 202-615-1 |
| European Inventory of Existing Commercial Chemical Substances (EINECS) | Listed. | ||
| EC Inventory | Listed. | ||
| United States Toxic Substances Control Act (TSCA) Inventory | Listed. | ||
| China Catalog of Hazardous chemicals 2015 | Listed. | ||
| New Zealand Inventory of Chemicals (NZIoC) | Listed. | ||
| Philippines Inventory of Chemicals and Chemical Substances (PICCS) | Listed. | ||
| Vietnam National Chemical Inventory | Listed. | ||
| Chinese Chemical Inventory of Existing Chemical Substances (China IECSC) | Listed. | ||
| Korea Existing Chemicals List (KECL) | Listed. | ||
SECTION 16: Other information
Information on revision
| Creation Date | July 15, 2019 |
|---|---|
| Revision Date | July 15, 2019 |
Abbreviations and acronyms
- CAS: Chemical Abstracts Service
- ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
- RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
- IMDG: International Maritime Dangerous Goods
- IATA: International Air Transportation Association
- TWA: Time Weighted Average
- STEL: Short term exposure limit
- LC50: Lethal Concentration 50%
- LD50: Lethal Dose 50%
- EC50: Effective Concentration 50%
References
- IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
- HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
- IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
- eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
- CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
- ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
- ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
- Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
- ECHA - European Chemicals Agency, website: https://echa.europa.eu/
Other Information
An added stabilizer or inhibitor can influence the toxicological properties of this substance; consult an expert.
Disclaimer: The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. We as supplier shall not be held liable for any damage resulting from handling or from contact with the above product.
Butyl methacrylate is included in Film Forming category. See more Butyl methacrylate price and marketing trends
Related Products
Industry News
More Safety Data Sheets