Product
Supplier
Encyclopedia
Inquiry
Home > Encyclopedia > Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide

Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide

Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide structure

Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide 

structure
  • CAS No:

    1562-94-3

  • Formula:

    C14H14N2O3

  • Chemical Name:

    Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide

  • Synonyms:

    Diazene,1,2-bis(4-methoxyphenyl)-,1-oxide;Azoxybenzene,4,4′-dimethoxy-;Diazene,bis(4-methoxyphenyl)-,1-oxide;Anisole,4,4′-azoxydi-;p-Azoxyanisole;4,4′-Azoxyanisole;4,4′-Azoxydianisole;p,p′-Azoxyanisole;p-Azoxydianisole;p,p′-Azoxydianisole;4,4′-Dimethoxyazoxybenzene;p,p′-Dimethoxyazoxybenzene;NSC 7959;Bis(4-methoxyphenyl)diazene oxide;74123-21-0;93485-76-8;1081826-35-8

  • Categories:

    Chemical Reagents  >  Organic Reagents

Description

bright yellow crystalline powderYellow monoclinic needles (in alcohol) or bright yellow crystals.


P-azoxyanisole appears as yellow monoclinic needles (in alcohol) or bright yellow crystals. (NTP, 1992)


P-azoxyanisole appears as yellow monoclinic needles (in alcohol) or bright yellow crystals. (NTP, 1992)

Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide Basic Attributes

258.27

258.27

216-348-3

ARL9G43P7E|4XSB9A1I17

694092|7959

DTXSID5024554

29270000

Characteristics

59.6

4.28

P-azoxyanisole appears as yellow monoclinic needles (in alcohol) or bright yellow crystals. (NTP, 1992)

1.1711 at 239° F (NTP, 1992)

118-136 °C

401.53°C (rough estimate)

206.6±31.5 °C

1.6419 (estimate)

less than 1 mg/mL at 70.7° F (NTP, 1992)

-20°C

8.26E-07mmHg at 25°C

Dust may form an explosive mixture in air. Insoluble in water.

Azo, Diazo, Azido, Hydrazine, and Azide Compounds

Explosive

P-AZOXYANISOLE is incompatible with strong oxidizing agents and strong reducing agents. (NTP, 1992)

Safety Information

NONH for all modes of transport

3

20/21/22-11

36/37/39-26-22-16-24/25

HM2966500

Xn-F

Flash point data for this chemical are not available; however, it is probably combustible. (NTP, 1992)

Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. A water spray may also be used. (NTP, 1992)

SMALL SPILLS AND LEAKAGE: If a spill of this chemical occurs, FIRST REMOVE ALL SOURCES OF IGNITION, then you should dampen the solid spill material with acetone and transfer the dampened material to a suitable container. Use absorbent paper dampened with acetone to pick up any remaining material. Seal your contaminated clothing and the absorbent paper in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with acetone followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned. STORAGE PRECAUTIONS: You should store this chemical under ambient temperatures, and keep it away from oxidizing materials and reducing materials. (NTP, 1992)

RECOMMENDED RESPIRATOR: Where the neat test chemical is weighed and diluted, wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter. (NTP, 1992)

Drug Information

SYMPTOMS: Symptoms of exposure to this compound may include irritation. ACUTE/CHRONIC HAZARDS: This compound may be harmful by inhalation, ingestion or skin absorption. When heated to decomposition it emits toxic fumes of carbon monoxide, carbon dioxide and nitrogen oxides. (NTP, 1992)

EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop. SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment. INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing. INGESTION: DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport the victim to a hospital. (NTP, 1992)

Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide Use and Manufacturing

Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide: ACTIVE

Computed Properties

Molecular Weight:258.27
XLogP3:3.1
Hydrogen Bond Acceptor Count:4
Rotatable Bond Count:4
Exact Mass:258.10044231
Monoisotopic Mass:258.10044231
Topological Polar Surface Area:59.6
Heavy Atom Count:19
Complexity:293
Covalently-Bonded Unit Count:1
Compound Is Canonicalized:Yes

Recommended Suppliers of Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide

Latest News on Diazene, 1,2-bis(4-methoxyphenyl)-, 1-oxide

Scan the QR Code to Share

Feedback & Suggestions
Send Message

Thank you for your feedback. If you require further assistance, please contact us by email at info@echemi.com or call us at +86-532-55729510.