Product
Supplier
Encyclopedia
Inquiry
Home > Encyclopedia > Methanediamine, hydrochloride (1:2)

Methanediamine, hydrochloride (1:2)

Methanediamine, hydrochloride (1:2) structure

Methanediamine, hydrochloride (1:2) 

structure
  • CAS No:

    57166-92-4

  • Formula:

    CH6N2.2ClH

  • Chemical Name:

    Methanediamine, hydrochloride (1:2)

  • Synonyms:

    Methanediamine,hydrochloride (1:2);Methanediamine,dihydrochloride;Methylenediamine dihydrochloride;Diaminomethane dihydrochloride;Methylenediamine bishydrochloride

  • Categories:

    Organic Chemistry  >  Amides

Description

PHYSICAL DESCRIPTION: White granular solid. Decomposes at approximately 275°F (changes to white puffy solid), then slowly darkens until total decomposition at approximately 464°F. (NTP, 1992)


Methylenediamine dihydrochloride is a white granular solid. Decomposes at approximately 275°F (changes to white puffy solid), then slowly darkens until total decomposition at approximately 464°F. (NTP, 1992)


Methylenediamine dihydrochloride is a white granular solid. Decomposes at approximately 275°F (changes to white puffy solid), then slowly darkens until total decomposition at approximately 464°F. (NTP, 1992)

Methanediamine, hydrochloride (1:2) Basic Attributes

118.99

118.00600

3664689

260-602-6

WZB0836N6G

DTXSID4025531

Characteristics

52

1.86590

0.879g/cm3

>300°C

82.6ºC at 760 mmHg

greater than or equal to 100 mg/mL at 70.7° F (NTP, 1992)

2-8°C

Water soluble.

Salts, Acidic

An acidic organic salt of an amine. In aqueous solution, behaves as an acid. Materials in this group are generally soluble in water. The resulting solutions contain moderate concentrations of hydrogen ions and have pH's of less than 7.0. They react as acids to neutralize bases. These neutralizations generate heat, but less or far less than is generated by neutralization of inorganic acids, inorganic oxoacids, and carboxylic acid. They usually do not react as either oxidizing agents or reducing agents but such behavior is not impossible. Many of these compounds catalyze organic reactions.

Safety Information

NONH for all modes of transport

3

36/37/38

26-36

P261, P264, P271, P280, P302+P352, P304+P340, P305+P351+P338, P312, P321, P332+P313, P337+P313, P362, P403+P233, P405, P501

H315

Flash point data for this chemical are not available; however, it is probably combustible. (NTP, 1992)

|Warning|H315 (100%): Causes skin irritation [Warning Skin corrosion/irritation]|P261, P264, P271, P280, P302+P352, P304+P340, P305+P351+P338, P312, P321, P332+P313, P337+P313, P362, P403+P233, P405, and P501|Aggregated GHS information provided by 4 companies from 1 notifications to the ECHA C&L Inventory. Each notification may be associated with multiple companies.

Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. (NTP, 1992)

SMALL SPILLS AND LEAKAGE: If you spill this chemical, you should dampen the solid spill material with water, then transfer the dampened material to a suitable container. Use absorbent paper dampened with water to pick up any remaining material. Seal your contaminated clothing and the absorbent paper in a vapor-tight plastic bag for eventual disposal. Wash all contaminated surfaces with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned. STORAGE PRECAUTIONS: You should store this material in a refrigerator. (NTP, 1992)

MINIMUM PROTECTIVE CLOTHING: If Tyvek-type disposable protective clothing is not worn during handling of this chemical, wear disposable Tyvek-type sleeves taped to your gloves. RECOMMENDED RESPIRATOR: Where the neat test chemical is weighed and diluted, wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter. Splash proof safety goggles should be worn while handling this chemical. Alternatively, a full face respirator, equipped as above, may be used to provide simultaneous eye and respiratory protection. (NTP, 1992)

Drug Information

EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop. SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. IMMEDIATELY call a hospital or poison control center even if no symptoms (such as redness or irritation) develop. IMMEDIATELY transport the victim to a hospital for treatment after washing the affected areas. INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing. INGESTION: DO NOT INDUCE VOMITING. Corrosive chemicals will destroy the membranes of the mouth, throat, and esophagus and, in addition, have a high risk of being aspirated into the victim's lungs during vomiting which increases the medical problems. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. IMMEDIATELY transport the victim to a hospital. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. Transport the victim IMMEDIATELY to a hospital. (NTP, 1992)

Methanediamine, hydrochloride (1:2) Use and Manufacturing

Methanediamine, hydrochloride (1:2): INACTIVE

Computed Properties

Molecular Weight:118.99
Hydrogen Bond Donor Count:4
Hydrogen Bond Acceptor Count:2
Exact Mass:118.0064537
Monoisotopic Mass:118.0064537
Topological Polar Surface Area:52
Heavy Atom Count:5
Complexity:2.8
Covalently-Bonded Unit Count:3
Compound Is Canonicalized:Yes

Recommended Suppliers of Methanediamine, hydrochloride (1:2)

Scan the QR Code to Share

Feedback & Suggestions
Send Message

Thank you for your feedback. If you require further assistance, please contact us by email at info@echemi.com or call us at +86-532-55729510.