Dimethylnaphthalene
-
Dimethylnaphthalene
structure -
-
CAS No:
28804-88-8
-
Formula:
C12H12
-
Chemical Name:
Dimethylnaphthalene
-
Synonyms:
Naphthalene,dimethyl-;Dimethylnaphthalene;1335-93-9;27457-31-4;65338-04-7;65338-08-1
- Categories:
-
CAS No:
Description
clear dark brown liquid after melting
Dimethylnaphthalene is a dark brown liquid. (NTP, 1992)
Dimethylnaphthalene is a dark brown liquid. (NTP, 1992)|1,2-dimethylnaphthalene is a dimethylnaphthalene carrying methyl groups at positions 1 and 2.
Characteristics
0
4.37
1.0052 g/cm3 @ Temp: 20 °C
69-700 °C
265 °C
>230 °F
1.605
less than 1 mg/mL at 73° F (NTP, 1992)
48 mm Hg at 124 °F ; 89 mm Hg at 167° F; 147 mm Hg at 199° F (NTP, 1992)|0.01 mmHg
Insoluble in water.
Hydrocarbons, Aromatic
DIMETHYLNAPHTHALENE is incompatible with oxidizers. (NTP, 1992)
Safety Information
3
22-24/25
P273, P391, P501
H400
This chemical is combustible. (NTP, 1992)
Not Classified
Fires involving this material can be controlled with a dry chemical, carbon dioxide or Halon extinguisher. A water spray may also be used. (NTP, 1992)
SMALL SPILLS AND LEAKAGE: If you spill this chemical, FIRST REMOVE ALL SOURCES OF IGNITION. Then, use absorbent paper to pick up all liquid spill material. Your contaminated clothing and absorbent paper should be sealed in a vapor-tight plastic bag for eventual disposal. Solvent wash all contaminated surfaces with 60-70% ethanol followed by washing with a soap and water solution. Do not reenter the contaminated area until the Safety Officer (or other responsible person) has verified that the area has been properly cleaned. STORAGE PRECAUTIONS: You should store this chemical under ambient temperatures, and keep it away from oxidizing materials. (NTP, 1992)
RECOMMENDED RESPIRATOR: Where the neat test chemical is weighed and diluted, wear a NIOSH-approved half face respirator equipped with an organic vapor/acid gas cartridge (specific for organic vapors, HCl, acid gas and SO2) with a dust/mist filter. (NTP, 1992)
Drug Information
ACUTE/CHRONIC HAZARDS: This compound may be harmful by inhalation, ingestion or skin absorption. It may cause irritation. When heated to decomposition it emits toxic fumes of carbon monoxide and carbon dioxide. (NTP, 1992)
EYES: First check the victim for contact lenses and remove if present. Flush victim's eyes with water or normal saline solution for 20 to 30 minutes while simultaneously calling a hospital or poison control center. Do not put any ointments, oils, or medication in the victim's eyes without specific instructions from a physician. IMMEDIATELY transport the victim after flushing eyes to a hospital even if no symptoms (such as redness or irritation) develop. SKIN: IMMEDIATELY flood affected skin with water while removing and isolating all contaminated clothing. Gently wash all affected skin areas thoroughly with soap and water. If symptoms such as redness or irritation develop, IMMEDIATELY call a physician and be prepared to transport the victim to a hospital for treatment. INHALATION: IMMEDIATELY leave the contaminated area; take deep breaths of fresh air. If symptoms (such as wheezing, coughing, shortness of breath, or burning in the mouth, throat, or chest) develop, call a physician and be prepared to transport the victim to a hospital. Provide proper respiratory protection to rescuers entering an unknown atmosphere. Whenever possible, Self-Contained Breathing Apparatus (SCBA) should be used; if not available, use a level of protection greater than or equal to that advised under Protective Clothing. INGESTION: DO NOT INDUCE VOMITING. If the victim is conscious and not convulsing, give 1 or 2 glasses of water to dilute the chemical and IMMEDIATELY call a hospital or poison control center. Be prepared to transport the victim to a hospital if advised by a physician. If the victim is convulsing or unconscious, do not give anything by mouth, ensure that the victim's airway is open and lay the victim on his/her side with the head lower than the body. DO NOT INDUCE VOMITING. IMMEDIATELY transport the victim to a hospital. (NTP, 1992)
1,2-dimethylnaphthalene
Dimethylnaphthalene Use and Manufacturing
Can inhibit the formation of paraffin wax network structure, improve the fluidity of oil
Naphthalene, dimethyl-: ACTIVE
Computed Properties
Molecular Weight:156.22
XLogP3:4.3
Exact Mass:156.093900383
Monoisotopic Mass:156.093900383
Heavy Atom Count:12
Complexity:150
Covalently-Bonded Unit Count:1
Compound Is Canonicalized:Yes
Recommended Suppliers of Dimethylnaphthalene
-
CN
5 YRS
Business licensedTrader Supplier of Intermediates,Building blocks,API,Silicones,Peptides,Lab chemicals,Biochemicals,Pharmaceuticals,Screening Compounds,Food Additives
Learn More Other Chemicals
-
6-Methyl-2′,3′-dideoxyadenosine
85326-07-4
-
2-[[2-(1H-indol-3-yl)acetyl]-methylamino]-2-phenyl-N-(4-propan-2-ylphenyl)acetamide
853138-65-5
-
Phenylmethyl docosanoate
85263-74-7
-
5,6,7,8-Tetrahydro-2-naphthalenesulfonic acid Formula
93-12-9
-
6-CHLORO-3-PHENYL-2-QUINOLINOL Formula
85274-64-2
-
2,5-Furandione, dihydro-, monopolyisobutylene derivs. Formula
67762-77-0
-
N-(4,4,5,5,6,6,7,7,8,8,9,9,10,10,11,11,11-Heptadecafluoroundecyl)maleimide Structure
852527-40-3
-
2-Benzothiazolecarboxaldehyde,5-methoxy-(5CI) Structure
854059-90-8
-
What is Benzamide, 5-(aminosulfonyl)-N-[(2-ethyloctahydro-1H-isoindol-1-yl)methyl]-2-methoxy-, hydrochloride (1:1)
85409-39-8
-
What is 3-(2,4-Dimethylphenyl)-5-phenyl-1H-1,2,4-triazole
85303-90-8