Product
Supplier
Encyclopedia
Inquiry
Home > Chemical CAS No.2 > Dichlorobenzene SDS

Dichlorobenzene Safety Data Sheets

SAFETY DATA SHEETS

According to the UN GHS revision 8

Version: 1.0

Creation Date: July 15, 2019

Revision Date: July 15, 2019

SECTION 1: Identification

1.1 GHS Product identifier

Product name

Dichlorobenzene

1.2 Other means of identification

Product number

-

Other names

-

1.3 Recommended use of the chemical and restrictions on use

Identified uses

Solvents (which become part of product formulation or mixture)

Uses advised against

no data available

1.4 Supplier's details

Company

Echemi.com

Address

Echemi.com

Telephone

Echemi.com

1.5 Emergency phone number

Emergency phone number

Echemi.com

Service hours

Monday to Friday, 9am-5pm (Standard time zone: UTC/GMT +8 hours).

SECTION 2: Hazard identification

2.1 Classification of the substance or mixture

Acute toxicity - Category 4, Oral

Skin irritation, Category 2

Skin sensitization, Category 1

Eye irritation, Category 2

Acute toxicity - Category 4, Inhalation

Specific target organ toxicity – single exposure, Category 3

Carcinogenicity, Category 2

Hazardous to the aquatic environment, short-term (Acute) - Category Acute 1

Hazardous to the aquatic environment, long-term (Chronic) - Category Chronic 1

2.2 GHS label elements, including precautionary statements

Pictogram(s)
Signal word

Warning

Hazard statement(s)

H302 Harmful if swallowed

H315 Causes skin irritation

H317 May cause an allergic skin reaction

H319 Causes serious eye irritation

H332 Harmful if inhaled

H335 May cause respiratory irritation

H351 Suspected of causing cancer

H400 Very toxic to aquatic life

H410 Very toxic to aquatic life with long lasting effects

Precautionary statement(s)
Prevention

P264 Wash ... thoroughly after handling.

P270 Do not eat, drink or smoke when using this product.

P280 Wear protective gloves/protective clothing/eye protection/face protection/hearing protection/...

P261 Avoid breathing dust/fume/gas/mist/vapours/spray.

P272 Contaminated work clothing should not be allowed out of the workplace.

P271 Use only outdoors or in a well-ventilated area.

P203 Obtain, read and follow all safety instructions before use.

P273 Avoid release to the environment.

Response

P301+P317 IF SWALLOWED: Get medical help.

P330 Rinse mouth.

P302+P352 IF ON SKIN: Wash with plenty of water/...

P321 Specific treatment (see ... on this label).

P332+P317 If skin irritation occurs: Get medical help.

P362+P364 Take off contaminated clothing and wash it before reuse.

P333+P317 If skin irritation or rash occurs: Get medical help.

P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing.

P304+P340 IF INHALED: Remove person to fresh air and keep comfortable for breathing.

P317 Get medical help.

P319 Get medical help if you feel unwell.

P318 IF exposed or concerned, get medical advice.

P391 Collect spillage.

Storage

P403+P233 Store in a well-ventilated place. Keep container tightly closed.

P405 Store locked up.

Disposal

P501 Dispose of contents/container to an appropriate treatment and disposal facility in accordance with applicable laws and regulations, and product characteristics at time of disposal.

2.3 Other hazards which do not result in classification

no data available

SECTION 3: Composition/information on ingredients

3.1 Substances

Chemical name Common names and synonyms CAS number EC number Concentration
Dichlorobenzene Dichlorobenzene 25321-22-6 246-837-7 100%

SECTION 4: First-aid measures

4.1 Description of necessary first-aid measures

If inhaled

Fresh air, rest. Refer for medical attention.

Following skin contact

Remove contaminated clothes. Rinse skin with plenty of water or shower. Refer for medical attention .

Following eye contact

First rinse with plenty of water for several minutes (remove contact lenses if easily possible), then refer for medical attention.

Following ingestion

Rinse mouth. Give one or two glasses of water to drink. Do NOT induce vomiting. Refer for medical attention .

4.2 Most important symptoms/effects, acute and delayed

Chronic inhalation of mist or vapors may result in damage to lungs, liver, and kidneys. Acute vapor exposure can cause symptoms ranging from coughing to central nervous system depression and transient anesthesia. Irritating to skin, eyes, and mucous membranes. May cause dermatitis. (USCG, 1999)

4.3 Indication of immediate medical attention and special treatment needed, if necessary

Immediate first aid: Ensure that adequate decontamination has been carried out. If patient is not breathing, start artificial respiration, preferably with a demand-valve resuscitator, bag-valve-mask device, or pocket mask, as trained. Perform CPR as necessary. Immediately flush contaminated eyes with gently flowing water. Do not induce vomiting. If vomiting occurs, lean patient forward or place on left side (head-down position, if possible) to maintain an open airway and prevent aspiration. Keep patient quiet and maintain normal body temperature. Obtain medical attention. Lindane and related compounds

SECTION 5: Fire-fighting measures

5.1 Suitable extinguishing media

Approach fire from upwind to avoid hazardous vapors and toxic decomposition products. Use water spray, dry chemical, foam, or carbon dioxide. Use water spray to keep fire-exposed containers cool. Extinguish fire using agent suitable for surrounding fire.

5.2 Specific hazards arising from the chemical

Special Hazards of Combustion Products: Poisonous vapors including hydrogen chloride gas, chlorocarbons, chlorine (USCG, 1999)

5.3 Special protective actions for fire-fighters

Wear self-contained breathing apparatus for firefighting if necessary.

SECTION 6: Accidental release measures

6.1 Personal precautions, protective equipment and emergency procedures

Avoid dust formation. Avoid breathing mist, gas or vapours.Avoid contacting with skin and eye. Use personal protective equipment.Wear chemical impermeable gloves. Ensure adequate ventilation.Remove all sources of ignition. Evacuate personnel to safe areas.Keep people away from and upwind of spill/leak.

6.2 Environmental precautions

Personal protection: filter respirator for organic gases and vapours adapted to the airborne concentration of the substance. Do NOT let this chemical enter the environment. Collect leaking and spilled liquid in sealable containers as far as possible. Absorb remaining liquid in sand or inert absorbent. Then store and dispose of according to local regulations.

6.3 Methods and materials for containment and cleaning up

Land spill: Dig a pit, pond, lagoon, or holding area to contain liquid or solid material. /SRP: If time permits, pits, ponds, lagoons, soak holes or holding areas should be sealed with an impermeable flexible membrane liner./ Dike surface flow using soil, sand bags, foamed polyurethane, or concrete. Absorb bulk liquid with fly ash, or cement power. Apply "universal" gelling agent to immobilize spill.

SECTION 7: Handling and storage

7.1 Precautions for safe handling

Handling in a well ventilated place. Wear suitable protective clothing. Avoid contact with skin and eyes. Avoid formation of dust and aerosols. Use non-sparking tools. Prevent fire caused by electrostatic discharge steam.

7.2 Conditions for safe storage, including any incompatibilities

Separated from aluminium, oxidants and food and feedstuffs.Store in cool, dry, well-ventilated location. Separate from oxidizing materials.

SECTION 8: Exposure controls/personal protection

8.1 Control parameters

Occupational Exposure limit values

Component Dichlorobenzene
CAS No. 25321-22-6

Recommended Exposure Limit: 15-Min Ceiling Value: 50 ppm (300 mg/cu m).


Biological limit values

no data available

8.2 Appropriate engineering controls

Ensure adequate ventilation. Handle in accordance with good industrial hygiene and safety practice. Set up emergency exits and the risk-elimination area.

8.3 Individual protection measures, such as personal protective equipment (PPE)

Eye/face protection

Wear tightly fitting safety goggles with side-shields conforming to EN 166(EU) or NIOSH (US).

Skin protection

Wear fire/flame resistant and impervious clothing. Handle with gloves. Gloves must be inspected prior to use. Wash and dry hands. The selected protective gloves have to satisfy the specifications of EU Directive 89/686/EEC and the standard EN 374 derived from it.

Respiratory protection

If the exposure limits are exceeded, irritation or other symptoms are experienced, use a full-face respirator.

Thermal hazards

no data available

SECTION 9: Physical and chemical properties and safety characteristics

Physical state

O-dichlorobenzene is a clear colorless liquid with a pleasant odor. Denser than water and insoluble in water. Flash point 150°F. Toxic by inhalation and ingestion. Used to make other chemicals, solvents, fumigants and insecticides and for many other uses.

Colour

Colorless liquid

Odour

Pleasant odor

Melting point/freezing point

1° F (NTP, 1992)

Boiling point or initial boiling point and boiling range

180.5ºC at 760mmHg

Flammability

Class IIIA Combustible Liquid: Fl.P. at or above 140°F and below 200°F.

Lower and upper explosion limit/flammability limit

2 TO 9% BY VOL IN AIR

Flash point

65.6ºC

Auto-ignition temperature

1198° F (USCG, 1999)

Decomposition temperature

no data available

pH

no data available

Kinematic viscosity

1.324 mPa.s at 25 deg C

Solubility

less than 1 mg/mL at 76.1° F (NTP, 1992)

Partition coefficient n-octanol/water

log Kow = 3.43

Vapour pressure

1 mm Hg at 68° F ; 1.5 mm Hg at 77° F (NTP, 1992)

Density and/or relative density

1.297g/cm3

Relative vapour density

5.05 (NTP, 1992) (Relative to Air)

Particle characteristics

no data available

SECTION 10: Stability and reactivity

10.1 Reactivity

Decomposes on burning. This produces toxic and corrosive gases including hydrogen chloride. Reacts with aluminium and oxidants. Attacks plastics and rubber.

10.2 Chemical stability

no data available

10.3 Possibility of hazardous reactions

Combustible liquid.O-DICHLOROBENZENE is sensitive to prolonged exposure to light. This chemical can react vigorously with oxidizers. It is incompatible with aluminum and aluminum alloys. It attacks some forms of plastics, rubber and coatings. (NTP, 1992).

10.4 Conditions to avoid

no data available

10.5 Incompatible materials

Strong oxidizers, aluminum, chlorides, acids, acid fumes.

10.6 Hazardous decomposition products

When heated to decomposition it emits toxic /hydrogen/ chloride fumes.

SECTION 11: Toxicological information

Acute toxicity

  • Oral: LD50 Guinea pig oral 0.8-2.0 ug/kg.
  • Inhalation: LC50 Mouse inhalation 6,825 mg/cu m/6 hr
  • Dermal: no data available

Skin corrosion/irritation

no data available

Serious eye damage/irritation

no data available

Respiratory or skin sensitization

no data available

Germ cell mutagenicity

no data available

Carcinogenicity

Evaluation: There is inadequate evidence in humans for the carcinogenicity of dichlorobenzenes. There is evidence suggesting a lack of carcinogenicity in experimental animals of ortho-dichlorobenzene. ... Overall evaluation: ortho-Dichlorobenzene is not classifiable as to its carcinogenicity to humans (Group 3). Dichlorobenzenes

Reproductive toxicity

no data available

STOT-single exposure

no data available

STOT-repeated exposure

no data available

Aspiration hazard

no data available

SECTION 12: Ecological information

12.1 Toxicity

  • Toxicity to fish: LC50; Species: Danio rerio (Zebra danio, age ~9 months, adult, weight 0.8 g, length 4.3 cm); Conditions: freshwater, static, 24 deg C, pH 7.8, hardness 350 mg/L CaCO3; Concentration: 180 mg/L for 96 hr /99% purity
  • Toxicity to daphnia and other aquatic invertebrates: EC50; Species: Daphnia magna (Water flea); Conditions: renewal, 25 deg C, pH >7; Concentration: 1700 ug/L for 24 hr; Effect: behavior, equilibrium
  • Toxicity to algae: EC50; Species: Pseudokirchneriella subcapitata (Green algae, initial concentration 500,000 cells/L); Conditions: static, 20 deg C; Concentration: 2200 ug/L for 96 hr; Effect: general growth
  • Toxicity to microorganisms: no data available

12.2 Persistence and degradability

AEROBIC: 1,2-Dichlorobenzene at 100 mg/L achieved 0% of its theoretical BOD using an activated sludge inoculum at 30 mg/L over a 4 week incubation period in the Japanese MITI test(1). 1,2-Dichlorobenzene was resistant to biodegradation in another Japanese MITI test study(2). Dichlorobenzene isomers were slowly biodegraded (6.3% of theoretical CO2 evolution in 10 weeks) in an alkaline soil sample(3). The rate constant for 1,2-dichlorobenzene in a heterogeneous aquifer at the Columbus Air Force Base, Mississippi was 0.0059 days-1, corresponding to a biodegradation half-life of about 117 days(4). 1,2-Dichlorobenzene is resistant to biodegradation in soils, with half-lives expected to be greater than 9 months(5).

12.3 Bioaccumulative potential

The sorption of 8 organic compounds by a representative green alga, Selenastrum capricornutum, was determined by GLC by a series of linear model experiments. The log10 bioconcentration factors (BCF), defined as the ratio of the concentration on/in the algae to the concentration in the aqueous medium, were as follows: benzene 3.32, toluene 3.18, chlorobenzene 3.69, 1,2-dichlorobenzene 4.17. The relation of log10 BCF correlation with log10 octanol-water partition coefficient (P) was determined to be log10 BCF= 0.46 log10 P + 2.36.

12.4 Mobility in soil

Experimental Koc values of 280(1) and 320(2) were determined for 1,2-dichlorobenzene in silt loam soils. A log Koc value of 3.7 was reported for 1,2-dichlorobenzene in sediment obtained from the Ise Bay, Japan(3) and a log Koc value of 4.3 was measured from sediment of Lake Ketelmeer, Netherlands(4). According to a recommended classification scheme(5), these soil Koc values suggest that 1,2-dichlorobenzene has moderate mobility in soil(SRC).

12.5 Other adverse effects

no data available

SECTION 13: Disposal considerations

13.1 Disposal methods

Product

The material can be disposed of by removal to a licensed chemical destruction plant or by controlled incineration with flue gas scrubbing. Do not contaminate water, foodstuffs, feed or seed by storage or disposal. Do not discharge to sewer systems.

Contaminated packaging

Containers can be triply rinsed (or equivalent) and offered for recycling or reconditioning. Alternatively, the packaging can be punctured to make it unusable for other purposes and then be disposed of in a sanitary landfill. Controlled incineration with flue gas scrubbing is possible for combustible packaging materials.

SECTION 14: Transport information

14.1 UN Number

ADR/RID: no data available IMDG: no data available IATA: no data available

14.2 UN Proper Shipping Name

ADR/RID: no data available IMDG: no data available IATA: no data available

14.3 Transport hazard class(es)

ADR/RID: no data available IMDG: no data available IATA: no data available

14.4 Packing group, if applicable

ADR/RID: no data available IMDG: no data available IATA: no data available

14.5 Environmental hazards

ADR/RID: Yes IMDG: Yes IATA: Yes

14.6 Special precautions for user

no data available

14.7 Transport in bulk according to IMO instruments

no data available

SECTION 15: Regulatory information

15.1 Safety, health and environmental regulations specific for the product in question

Chemical name Common names and synonyms CAS number EC number
Dichlorobenzene Dichlorobenzene 25321-22-6 246-837-7
European Inventory of Existing Commercial Chemical Substances (EINECS) Listed.
EC Inventory Listed.
United States Toxic Substances Control Act (TSCA) Inventory Not Listed.
China Catalog of Hazardous chemicals 2015 Not Listed.
New Zealand Inventory of Chemicals (NZIoC) Listed.
Philippines Inventory of Chemicals and Chemical Substances (PICCS) Listed.
Vietnam National Chemical Inventory Not Listed.
Chinese Chemical Inventory of Existing Chemical Substances (China IECSC) Listed.
Korea Existing Chemicals List (KECL) Not Listed.

SECTION 16: Other information

Information on revision

Creation Date July 15, 2019
Revision Date July 15, 2019

Abbreviations and acronyms

  • CAS: Chemical Abstracts Service
  • ADR: European Agreement concerning the International Carriage of Dangerous Goods by Road
  • RID: Regulation concerning the International Carriage of Dangerous Goods by Rail
  • IMDG: International Maritime Dangerous Goods
  • IATA: International Air Transportation Association
  • TWA: Time Weighted Average
  • STEL: Short term exposure limit
  • LC50: Lethal Concentration 50%
  • LD50: Lethal Dose 50%
  • EC50: Effective Concentration 50%

References

  • IPCS - The International Chemical Safety Cards (ICSC), website: http://www.ilo.org/dyn/icsc/showcard.home
  • HSDB - Hazardous Substances Data Bank, website: https://toxnet.nlm.nih.gov/newtoxnet/hsdb.htm
  • IARC - International Agency for Research on Cancer, website: http://www.iarc.fr/
  • eChemPortal - The Global Portal to Information on Chemical Substances by OECD, website: http://www.echemportal.org/echemportal/index?pageID=0&request_locale=en
  • CAMEO Chemicals, website: http://cameochemicals.noaa.gov/search/simple
  • ChemIDplus, website: http://chem.sis.nlm.nih.gov/chemidplus/chemidlite.jsp
  • ERG - Emergency Response Guidebook by U.S. Department of Transportation, website: http://www.phmsa.dot.gov/hazmat/library/erg
  • Germany GESTIS-database on hazard substance, website: http://www.dguv.de/ifa/gestis/gestis-stoffdatenbank/index-2.jsp
  • ECHA - European Chemicals Agency, website: https://echa.europa.eu/

Disclaimer: The above information is believed to be correct but does not purport to be all inclusive and shall be used only as a guide. The information in this document is based on the present state of our knowledge and is applicable to the product with regard to appropriate safety precautions. It does not represent any guarantee of the properties of the product. We as supplier shall not be held liable for any damage resulting from handling or from contact with the above product.

Industry News

More Safety Data Sheets

Feedback & Suggestions
Send Message

Thank you for your feedback. If you require further assistance, please contact us by email at info@echemi.com or call us at +86-532-55729510.